Skip to content

SODIMAS · Platform

SODIMAS push-button panels — Cyntra, Evolya, Synia, Démon

SODIMAS offers its push-button panels in several ranges — Cyntra, Evolya, Synia, Démon, Angel, Blackpad — which share the same technical base: micro-stroke buttons, 24 V DC LED lighting and compliance with the EN 81-70 accessibility standard.

These ranges differ in appearance, diameter, finish and resistance to vandalism. Some also comply with EN 81-71, which deals with resistance to acts of vandalism.

One point conditions compatibility more than any other: most of these buttons only work with a microprocessor cabinet. On an installation with a relay cabinet, relaying must be provided. The Démon range is the exception and works with all cabinets.

Technical sheet

Technical specifications

Standards
EN 81-70 — accessibility for disabled persons · EN 81-71 — vandal resistance, depending on the range
Technology
Micro-stroke buttons · 50 mA maximum contact for call buttons · Contact characteristics: 30 V maximum
Lighting
Central blue LED 24 V DC — 15 mA · Polycarbonate diffuser · Green, red or blue LED indicators depending on the function · Telephone button: green and yellow LED 24 V DC — 15 mA
Functions without lighting
Open / close button: 1 NO + 1 NC · Alarm button on some ranges: 1 NO + 1 NC
Connection
JST 4-pin connectors · 0.75 mm² cable · Crimped connector
Cabinet compatibility
Microprocessor cabinet required for most ranges · Relay cabinet: relaying to be provided · Démon range: compatible with all cabinets
Environment
Operating temperature: 0 to 50 °C · Storage temperature: −20 to +70 °C
Locations
Column · Car faceplate · Landing faceplate · Horizontal accessible faceplate
Fixing
Plastic nuts on most ranges · Through mounting with knurled ring tightening on some versions · Flanges: guide stud and button
Metal flanges
Gloss or epoxy RAL 9005 black finish · Embossed symbol and integrated braille · Compliant with EN 81-70 and EN 81-71 anti-vandal
Finishing accessories
Blanking plug for the Evolya flange hole at landing · Four finishes: brushed stainless steel grain 220, Lino stainless steel, engraved stainless steel, matt RAL 7032 painted stainless steel · Dimensions 60 × 33 mm in 1.5 or 3 mm thickness · Supplied with flat washer and two M3 serrated nuts

Comparison of the documented variants

VariantSheet ref.FinishStandardsWeightBearing forceEvolya / Synia compatible
Cyntra XL V227 100 024Black stainless steel, Ø 60 mm, raised ABS symbolEN 81-70 annex G (without BIP)62 g——
Cyntra IP6527SO021P00041Black stainless steelEN 81-70 (2018) and EN 60529 — IP65——No — usable with NG240
Cyntra black mirror27SO021P00066Black mirror stainless steelEN 81-7018 g3,5 à 5,5 NYes
Cyntra brushed gold27SO021P00067Brushed gold stainless steelEN 81-70——Yes
Brushed stainless steel back micro-stroke27 100 022Brushed stainless steelEN 81-7018 g3,5 à 5,5 NYes
Full stainless steel micro-stroke27 100 023Stainless steelEN 81-70 and EN 81-7163 g5,5 à 7 NYes
Démon BIP27 100 017Anti-vandal stainless steel, grey or brushed goldEN 81-70 and EN 81-7132 g—Yes — and all cabinets

Installation architecture

Parts are divided into four zones. Identifying the zone concerned is the first diagnostic reflex: it immediately narrows down the possible references.

Car faceplate

It groups the floor buttons, door opening and closing, the alarm and the display. SODIMAS ranges are mounted on it as a column or a horizontal faceplate for accessibility.

Related parts: car faceplate · button · column

Landing faceplate

Call button, registration indicator and, depending on the configuration, position display and direction arrows.

Related parts: landing faceplate · landing button · display

Flanges and trim

The flange surrounds the button; the insert carries the engraved symbol and the braille. These are the parts that wear out first.

Related parts: flange · insert · disc

Link with the controller

Connection by 4-pin JST connectors in 0.75 mm². The nature of the cabinet — microprocessor or relay — determines compatibility.

Related parts: wiring · connector · board

Points of attention

  • First check the nature of your cabinet: most of these buttons require a microprocessor cabinet. On a relay cabinet, relaying is necessary — except with the Démon range, compatible with all cabinets.
  • Beware of the Cyntra IP65 version: unlike the other Cyntra variants, it is not compatible with the Evolya and Synia ranges. Its documentation intends it for NG240 technology. Do not substitute it for a standard Cyntra without checking.
  • The protection rating distinguishes uses: IP65 per EN 60529 on the dedicated version, versus IP50 on the front for the Cyntra XL V2. For an environment exposed to water or dust, it is the deciding criterion.
  • Cyntra XL V2 is fitted in Ø 60 mm with a raised ABS symbol and black stainless steel face: it is the version intended for accessibility faceplates.
  • The actuation force varies from single to double depending on the ranges, from 3.5 to 7 N: a button that is too hard or too soft is immediately noticeable in a mixed bank. Weight follows the same logic, from 18 to 63 g.
  • Démon buttons can be used with the Evolya and Synia ranges, which eases partial replacements on a mixed installed base.
  • On a landing door, replacing an Evolya flange leaves a visible hole in the frame: a blanking plug exists in four finishes and two thicknesses to hide it.
  • Keep the finish consistent across the whole bank: brushed stainless steel, grey or gold anti-vandal stainless steel, black face. A mismatched button is noticeable.
  • Raised and braille marking is required by EN 81-70 on controls intended for users: do not remove it when replacing.

Get a quote

State the part reference if you know it, the number of levels and accesses of the unit, the type of wiring and your wilaya. A photo of the part in place and its markings confirms the match. KMY confirms the final price, availability and delivery time in Algeria.

Search all SODIMAS Boutonnerie parts in the catalogue ↗

Source of the specifications: SODIMAS data sheets ref. 27 100 017, 27 100 020, 27 100 021, 27 100 022, 27 100 023, 27 100 024, 27 100 025, 27SO021P00041, 27SO021P00066, 27SO021P00067 and 27SO021P00192. Data reproduced for information only; only the manufacturer’s documentation is authoritative. Specifications may change between versions.

FAQ

Frequently asked questions about SODIMAS push-button panels

What are the SODIMAS button ranges?

SODIMAS offers its push-button panels in several ranges: Cyntra, Evolya, Synia, Démon, Angel and Blackpad. They share a common technical base — micro-stroke buttons, 24 V DC LED lighting, EN 81-70 compliance — and differ in appearance, diameter, finish and resistance to vandalism.

Do these buttons work with any cabinet?

No. Most ranges require a microprocessor cabinet. On an installation with a relay cabinet, relaying must be provided. The Démon range is the exception: it works with all cabinets. This is the first point to check before ordering.

What is the supply voltage of SODIMAS buttons?

Lighting is by 24 V DC LEDs, with a consumption of 15 mA. The call button contact accepts 50 mA maximum, at 30 V maximum. Connection is by 4-pin JST connectors on 0.75 mm² cable.

What does EN 81-70 and EN 81-71 compliance bring?

EN 81-70 deals with accessibility: it notably requires raised and braille marking of controls intended for users. EN 81-71 deals with resistance to vandalism. The Démon ranges and full stainless steel micro-stroke buttons meet both.

Can several ranges be mixed on the same unit?

Technically yes when cabinet compatibility is respected, and Démon buttons can indeed be used with the Evolya and Synia ranges. But the actuation force varies from 3.5 to 7 N depending on the range, and finishes differ: a mixed bank is noticeable to the touch as well as to the eye. Note also the Cyntra IP65 version, which is not compatible with Evolya or Synia.

Which version to choose for a damp or dusty environment?

The Cyntra IP65 version complies with EN 60529 with an IP65 protection rating, versus IP50 on the front for the Cyntra XL V2. It is the variant to choose outdoors, in car parks or in industrial environments. Do check its compatibility, however: it is not paired with the Evolya and Synia ranges and targets NG240 technology.

Do the flanges comply with accessibility rules?

Yes. SODIMAS metal flanges carry an embossed symbol and integrated braille marking, compliant with EN 81-70. They also meet EN 81-71 on resistance to vandalism. They come in a gloss finish and in RAL 9005 black epoxy.

A reference to find? Send us the marking on your part.

Let’s talk. Our teams reply within 48 hours with a first estimate.

Request a quote