Skip to content

SODIMAS · Platform

SoLIMAX — SIL3 absolute position sensor

SoLIMAX measures the absolute position of the car. Unlike incremental counting, it knows the real elevation at all times thanks to a coded stainless steel strip run in the shaft — and keeps this position even after a prolonged power cut.

It is not a simple position sensor: it is a SIL3-certified safety component that integrates and monitors the limit switches, the drift zone of amendment A3, the levelling and early door opening zone, speed control and overspeed.

It communicates with the controller via CANopen bus and is found notably on installations fitted with QI Touch.

Technical sheet

Technical specifications

Measuring principle
Absolute linear · Position accuracy: 2 mm · Resolution: 0.0625 mm
Speed
3.5 kW
Communication
CANopen bus · Diagnostic LEDs
Sensor
Dimensions: H 370 × W 85 × D 39 mm · Weight: 0.9 kg · IP54 protection per EN 60529 · Operating temperature: −20 to +70 °C
Magnetic strip
15-bit coding · Travel: 100 m in QI, 268 m maximum · Dimensions: width 10 mm, thickness 1.35 mm · Weight: 0.52 kg per metre · Stainless steel back, IP67 · Tension and break monitoring by spring and IP54 safety contact
Integrated safety devices
Upper and lower travel limit: 50 mm, adjustable from 30 to 100 mm · High inspection travel limit: 1300 mm below the top level sill, adjustable from 1300 to 10,000 mm · Low inspection travel limit: 1700 mm above the bottom level sill, adjustable from 1300 to 10,000 mm · A3 anti-drift zone: 200 mm, adjustable from 20 to 350 mm · Pre-opening safety: 200 mm zone, maximum speed 0.8 m/s · Levelling zone: 140 mm, adjustable from 20 to 140 mm, maximum speed 0.3 m/s · Overspeed in normal mode: 115 % of rated speed · Maintenance mode: overspeed at 0.63 m/s +5 %, with direction control · Slow-down control: deceleration above 1.4 m/s²
Certification
SIL3 safety component · TÜV approval no. TUV-A-AT-1/12/316CEES · Compliant with Lifts Directive 95/16/EC annex 5
Standards
EN 81-1 + A3 · EN 61508 · EN 12015 / EN 12016 (EMC) · EN 60068-2-6, EN 60068-2-27, EN 60068-2-29 (vibration)

Installation architecture

Parts are divided into four zones. Identifying the zone concerned is the first diagnostic reflex: it immediately narrows down the possible references.

Sensor on the car roof

The sensor reads the magnetic strip as it passes and calculates the absolute position. Its LEDs allow immediate on-site diagnosis.

Related parts: Solimax · sensor · rangefinder

Magnetic strip in the shaft

Stainless steel strip coded on 15 bits, stretched over the whole travel. A spring and a safety contact monitor its tension and detect a break.

Related parts: magnetic strip · Limax

Safety box

It carries the SIL3-certified safety functions and communicates with the controller via CANopen bus.

Related parts: Solimax box · board

Link with the controller

The CANopen bus transmits position and safety states. On QI Touch installations, the Solimax learning is one of the commissioning steps.

Related parts: QI Touch · board · wiring

Points of attention

  • SoLIMAX is a SIL3-certified safety component: replacing it is a supervised intervention, with tests before return to service.
  • The length of magnetic strip depends on the travel: 100 m in Quick Install configuration, 268 m maximum. Measure the actual travel before ordering.
  • Safety values are adjustable within defined ranges — anti-drift zone from 20 to 350 mm, levelling from 20 to 140 mm, travel limits from 30 to 100 mm. Any setting outside the range is refused by the device.
  • The maximum permitted speed is 3 m/s in Quick Install and 10 m/s in full configuration: check your unit’s rated speed.
  • The strip tension monitoring contact is part of the safety chain: a slack or broken strip stops the unit.
  • On a QI Touch installation, the Solimax learning is a separate commissioning step, to be redone after replacement.

Get a quote

State the part reference if you know it, the number of levels and accesses of the unit, the type of wiring and your wilaya. A photo of the part in place and its markings confirms the match. KMY confirms the final price, availability and delivery time in Algeria.

Search all SoLIMAX parts in the catalogue ↗

Source of the specifications: SODIMAS SoLIMAX data sheet ref. 27SO053P00007FR and EU declaration of conformity ref. 25-04-H067 (29/04/2025). Data reproduced for information only; only the manufacturer’s documentation is authoritative. Specifications may change between versions.

FAQ

Frequently asked questions about SoLIMAX

What is the SoLIMAX sensor?

SoLIMAX is an absolute position sensor for lifts. It measures the car’s real elevation with an accuracy of 2 mm by reading a coded stainless steel strip run in the shaft, and keeps this position even after a prolonged power cut. It is also a SIL3-certified safety component.

What safety functions does SoLIMAX provide?

It integrates and monitors the extreme and inspection limit switches, deceleration control, the drift zone of amendment A3, the levelling and early door opening zone, speed control in normal and maintenance mode, as well as overspeed, set at 115 % of rated speed.

What length of magnetic strip should be planned?

The permissible travel is 100 m in Quick Install configuration and 268 m maximum. The strip is 10 mm wide and 1.35 mm thick and weighs 0.52 kg per metre. Its stainless steel back is rated IP67.

What lift speed does SoLIMAX accept?

Up to 3 m/s in the Quick Install configuration, and up to 10 m/s in the full configuration. The measurement resolution is 0.0625 mm.

Is SoLIMAX approved?

Yes. It is certified as a SIL3 safety component under number TUV-A-AT-1/12/316CEES, compliant with EN 81-1 amendment A3, EN 61508 and the electromagnetic compatibility standards EN 12015 and EN 12016. It meets annex 5 of Lifts Directive 95/16/EC.

A reference to find? Send us the marking on your part.

Let’s talk. Our teams reply within 48 hours with a first estimate.

Request a quote