Skip to content

SODIMAS · Platform

SODIMAS TA, TS and GS winches — features and maintenance

SODIMAS offers its geared winches in three families: TA, TS and GS. All are based on an asynchronous motor driven by a frequency drive and accept closed-loop operation.

The TA range — TA 125, TA 140 and TA 150 — covers most needs in modernisation as in new builds, with a compact footprint. The TS models go up in load and power, in sheave or drum versions. The GS 140 stands out with a disc brake where the rest of the range uses drum brakes.

The choice is first based on the permissible shaft load — 2,000 kg for the TA 125, 2,800 kg for the TA 140, 3,500 kg for the TA 150 — then on the travel served and the desired speed.

Technical sheet

Technical specifications

Machine type
Geared winch · Asynchronous motor driven by frequency drive · Prepared for closed-loop operation
Motor power supply
400 V three-phase, 50 Hz
Brake
110 V DC · 1 A on TA 125 and TA 140 · 1.5 A on TA 150
Protection and insulation
IP21 protection rating · Insulation class F · Duty factor 40 %
Groove profile
35° V-groove across the whole range
Orientation
TA 125 and TA 150: left and right versions · TA 140: horizontal or vertical mounting
TA 150 equipment
Brake monitoring contacts · Large oil level display · Manual rescue handwheel · Closed-loop encoder protection · Rope guards
Braking system
Drum brake on the TA and TS ranges · Disc brake on the GS 140 · Separate adjustments: braking force, shoes, opening distance and synchronous adjustment
Lubrication
Total EP460 oil, SODIMAS reference 02 000 105 · First replacement after 6 months of service or 500 hours · Then every 24 months, not exceeding 36 months · Full replacement after more than a year of shutdown
Manufacturing
Made in France

Comparison of the three models

FeatureTA 125TA 140TA 150
Motor speed1440 rpm1440 rpm1465 rpm
Shaft load2. Choosing the layout2. Load capacity3 m/s with Quick Install · 10 m/s maximum
Winch weight195 kg195 kg310 kg
Motor current8,5 A7,3 A15 A
Travel served30 m50 m50 m
Number of ropes445
Cable diameter8 to 11 mm8 to 11 mm10 to 13 mm
Groove pitch16 mm16 mm17 mm
Brake voltage and current110 V DC — 1 A110 V DC — 1 A110 V DC — 1.5 A
Payload320 à 400 kg320 kg450 to 630 kg
Sheave diameter520 and 570 mm425, 480, 520 and 560 mm580 mm
Car speed0,6 à 1 m/s0,6 à 0,8 m/s0,6 à 1 m/s
Power4 kW3. The travel7,5 kW
Reduction ratio1/371/511/45

Recommended maintenance programme

Point to checkExpected valueFrequency
Brake operationCorrect3. Comparing suppliers
Brake disc thicknessGreater than 5 mm3. Comparing suppliers
Bearing noiseNo abnormal noise3. Comparing suppliers
Motor vibrationLess than or equal to 20 µm3. Comparing suppliers
Bearing lubricationNormal operation3. Comparing suppliers
Current under loadLess than or equal to the average current3. Comparing suppliers
Sheave fixingNo play6 months
Sheave groovesNo pronounced wear6 months
Anti-overflowNo displacement from the nominal position6 months
Winding insulation resistanceGreater than or equal to 3 MΩ6 months
Electrical connectionsNo play6 months
Machine cleanlinessDust-freeAs needed

This programme is the one recommended by the manufacturer. It does not replace the periodic statutory checks of the installation.

Installation architecture

Parts are divided into four zones. Identifying the zone concerned is the first diagnostic reflex: it immediately narrows down the possible references.

Winch and gearbox

Asynchronous motor, gearbox and traction sheave form the load-bearing assembly. The gearbox oil level is a periodic check point — the TA 150 has a dedicated display.

Related parts: TA winch · motor · oil

Traction sheave

35° V-groove, from 425 to 580 mm in diameter depending on the model and load. The pitch and number of grooves determine the choice of ropes.

Related parts: TA125 sheave · TA150 sheave · rope guard

Braking

110 V DC brake, with monitoring contacts on the TA 150. The shoes and linings are wear parts followed up in maintenance.

Related parts: TA125 brake · shoe · lining

Position feedback

The assembly is prepared for closed-loop operation; the TA 150 receives encoder protection.

Related parts: encoder · rotating parts guard

Points of attention

  • The deciding criterion is the permissible shaft load: 2,000 kg on TA 125, 2,800 kg on TA 140, 3,500 kg on TA 150. It includes the car, the payload and the counterweight.
  • The travel served differs: 30 m on the TA 125 versus 50 m on the TA 140 and TA 150. This is a point often overlooked when modernising a tall building.
  • The TA 125 and TA 150 exist in left and right versions: specify the orientation, it cannot be changed afterwards.
  • The TA 140 accepts horizontal or vertical mounting, which makes it the choice for constrained machine rooms.
  • The diameter and number of ropes change with the model: 4 ropes of 8 to 11 mm on TA 125 and TA 140, 5 ropes of 10 to 13 mm on TA 150. The groove pitch goes from 16 to 17 mm.
  • All these winches run on 400 V three-phase at 50 Hz with a 40 % duty factor: check suitability with the unit’s actual traffic.
  • The brake is 110 V DC across the whole range, but the current differs: 1 A on TA 125 and TA 140, 1.5 A on TA 150.
  • The recommended oil is Total EP460. The first replacement takes place at 6 months or 500 hours, then every 24 months without exceeding 36 months. A machine left stopped for more than a year requires a complete oil change before returning to service.
  • Black, foul-smelling oil must be replaced immediately, without waiting for the due date: colour, smell and cleanliness are the three ageing indicators to check.
  • On a drum brake, the gap between lining and drum must stay below 0.3 mm once the brake is energised, with no residual friction. The brake disc is replaced below 5 mm thickness.

Get a quote

State the part reference if you know it, the number of levels and accesses of the unit, the type of wiring and your wilaya. A photo of the part in place and its markings confirms the match. KMY confirms the final price, availability and delivery time in Algeria.

Search all Treuils TA / TS / GS parts in the catalogue ↗

Source of the specifications: SODIMAS range sheet for TA winches ref. 27SO053P00064 (06/2019) and commissioning and maintenance manual for TA, TS and GS winches ref. 02999100 (26/04/2022). Data reproduced for information only; only the manufacturer’s documentation is authoritative. Specifications may change between versions.

FAQ

Frequently asked questions about TA / TS / GS winches

What is the difference between TA 125, TA 140 and TA 150?

Mainly the permissible shaft load: 2,000 kg for the TA 125, 2,800 kg for the TA 140 and 3,500 kg for the TA 150. Then come power (4, 3.5 and 7.5 kW), number of ropes (4, 4 and 5) and winch weight (195, 195 and 310 kg). The TA 125 serves 30 m of travel, the other two 50 m.

What payload and speed do these winches allow?

The TA 125 covers 320 to 400 kg payload at 0.6 to 1 m/s, with 520 or 570 mm sheaves. The TA 140 covers 320 kg at 0.6 to 0.8 m/s with 425 to 560 mm sheaves. The TA 150 covers 450 to 630 kg at 0.6 to 1 m/s with a 580 mm sheave.

Are these winches suitable for a modernisation?

Yes, the TA range was designed for modernisation as well as new builds. Its compact size and the possibility of horizontal or vertical mounting on the TA 140 ease integration into an existing machine room.

What is the brake voltage on a TA winch?

110 V DC across the whole range. The current depends on the model: 1 A on TA 125 and TA 140, 1.5 A on TA 150. The TA 150 also has brake monitoring contacts.

Can they be used in closed loop?

Yes, all three models are prepared for closed-loop operation. The TA 150 receives a dedicated encoder protection. Closed loop improves stopping accuracy and starting comfort.

Which oil to use and how often to change it?

The recommended oil is Total EP460, referenced 02 000 105 in the SODIMAS catalogue. The first replacement takes place after 6 months of operation or 500 hours, then every 24 months without exceeding 36 months. A machine stopped for more than a year must be drained completely. Black, foul-smelling oil is changed immediately.

When should the disc or sheave be replaced?

The brake disc is replaced as soon as its thickness falls below 5 mm — it is a quarterly check. The traction sheave is replaced when its grooves are worn, wear generally caused by a groove irregularity or a tension difference between the ropes.

A reference to find? Send us the marking on your part.

Let’s talk. Our teams reply within 48 hours with a first estimate.

Request a quote